Audison bit Ten

Power Suply

Voltage
11 ÷ 15 VDC

Idling current
0.4 A

Switched off without DRC
< 2.5 mA

Switched off with DRC
< 4.0 mA

Remote In voltage
7 ÷15 VDC (1.3 mA)

Remote Out voltage
12 VDC (130 mA)

Distorsion-THD@1 kHz, 1VRMS Output
0.005 %

Bandwidth@ -3dB
10 ÷ 22 kHz

S/N Ratio @ A weighted
96 dBA

Channel Separation (@1 kHz)
85 dB

Input sensitivity (Low Level)
0.6 ÷ 5 VRMS

Input sensitivity (High Level)
2.0 ÷ 15 VRMS

Max Output Levels
4 VRMS

Input impedance (AUX)
15 kΩ

Input impedance (High Level)
2.2 kΩ

Inputs
Low Level (Pre In): AUX L/RHigh Level (Spk In): FL-FR-RL-RR, Phone In

Outputs
Analog Pre Out: Ch1 ÷ Ch5

 
 

Crossover

Type
12/24 dB Linkwitz6/12/18/24 dB Butterworth

Mode
Full/HiPass/LowPass/BandPass (indipendent)

 
 

Equalizer

Type
31 Band, ISO 1/3 Oct, 20 Hz ÷ 20 kHz

Gain
± 12 dB

Delay
0 ÷ 22 ms (748 cm)

 
 

Time Alignment

Distance
0 ÷ 510 cm

Delay
0 ÷ 15 ms

Step
0.08 ms; 2.8 cm

Fine set step
0.02 ms; 0.7 cm

 
 

Size

WxHxD
191x34x131 mm

Weight
0.6 kg

Audo DSPand converters
32 bit Cirrus Logic (Clock speed: 147 MHz) Digital Signal Processing chip and A/D D/A converters working in PCM at 48 kHz with 24 bit resolution. The processor speed allows the user to hear and verify in real time the changes applied during the tuning

Audio Inputs
4 independent high-level channels with automatic summing capability1 analog low-level stereo auxiliary input1 high-level momentary audio interrupt input (with priority) on Phone Mute cable (settable through PC)

Audio Outputs
5 independent analog PRE channels featuring adjustable level

ControlConnections
1 USB /B (2.0) connector for PC connection1 AC Link control bus connectors for DRC1 input for external Mute (settable through PC)

Configuration
Guided procedure that, thanks to a wide range of set names, provides the ability to assign each component to the bit Ten connections and automatically coordinate their functioning

Turn-onControls
ART™, Automatic Remote Turn on/off, selectable from Hi-Level Front L. The ART™ can be enabled through an external switchThrough the Remote INThrough the car ignition key with memory functionThrough the DRC (optional)Automatically through the hands-free phone kit

In/Out Volume
Input sensitivity manual adjustable for the Master Hi-Level inputs (with supplied Test CD)Manual input sensitivity adjustment for auxiliary inputsIndependent level control for each output channel for system fine tuning (-40 ÷ 0 dB)

De-equalization
Automatic de-equalization of signal fed into the high-level inputs (with supplied Test CD) if necessary. It can also be performed without the PC

Equalizers
31-band graphic equalizer (1/3 Oct.; ±12 dB) for each output channels

Crossover Filter
Filter typology: selectable; Hi-pass, Lo-pass, Full Range, Band pass with independent selectable cut-off slopeCut-off frequency: 70 steps available from 20 Hz to 20k HzCut-off slope: selectable; 6 to 24 dB/Oct.Selectable alignment: Linkwitz or ButterworthMute: selectable for each output (On/Off)Phase: selectable for each output (0°/180°)

Signal channelsreconstruction
It can reconstruct a stereo output signal from a multi-channel input signal. In addition it can reconstruct rear, centre and subwoofer output channels from a stereo input

Time Alignment
Guided procedure for the speaker distance data entry with an automated calculation (distance to time) for each channel for accurate delay times. System also provides for manual fine tuning of delay (0.02 ms fine set)

DRC (optional)
Master Volume, Subwoofer Volume, Balance and Fader controls, Input selection, Memory selection, Adjustable display brightness

Memory
2 presets separately managed and recalled by the DRC (optional)

bit Ten software
Microsoft Windows (XP, 7 and Vista) based software with “Standard” and “Expert” operating modes; screen resolution: 1024x600 px min.